router configuration commands step by step
router configuration commands step by step
7) Next is the configuration of interfaces with the Network IP addresses. Thus we are prepared with the IP addresses to be allocated to the interfaces on Router1 and Router2. It is also used to check the loopback interface. In reverse routing, all the IP packets with the destination address 10.180.146.28 will be destined to the device having interface IP 10.180.146.5. Step2: Configure a Router Hostname. This information can be extracted from the manual of the router. 4) To check our configuration on interfaces, we can run one show command as given below: 5) To save our configuration we use the write command. #2) For performing configuration on the router from the remote end using the console port we need to enable the configure terminal mode. Here, we can keep the backup of the router’s configuration and save it in a file format. By using the first network cable, connect the WAN port of the router to the modem or DSL through which the Internet connection is going to be provided. #3) Basic Router Settings: Through the web interface we can make the basic settings in the router. Now by using the second network cable, connect the LAN port of the router to the PC’s network port. The above output shows that the ping is successful and the IP is reachable. Thus it is deployed worldwide in spite of it’s complex and long configuration processes. Whenever we boot our Router first, there is always some default configuration that exists into it. See below as how the output of the above commands will appear on the command line with the help of a similar example: 10) The next step is to manually configure the host device PC1 and PC2 with the IP’s 22.214.171.124 and 126.96.36.199 and with the subnet mask 255.255.255.224 respectively. Router# config terminal Step 3: Enter the router rip command Router(config)#router rip Step 4: Add the network number to use RIP and repeat this step for all the numbers. But in this tutorial, we will explore the basic configuration commands that are used in making the routers operational in any of the network and set-up of routers and switches in a networking system. Example: Telnet 10.180.196.42 Login: Router1 (specify login id, here login id is Router1) Password: ******** Router> enable. #5) Now define the hostname ( router name ) and password. The output will appear in the command line as much similar as shown in the below screenshot: If you want to see how it will appear in the command line, then please take a look at the below screenshot: From the above-detailed output of show commands, our configuration has been checked and found OK. Enlisted below is the comparison between home routers and business purpose routers. The first parameter is the Wizard, here we can set the Wi-Fi network name and password and can modify the default password that is used to log in the device to make it a more secure one for personal use. Router# configure terminal Router (config)#. Step3: Configure IP addresses for Router Interfaces It is one of the important commands and can be used locally on your PC as well to check the IP reachability. Router> configure terminal RouterX (config)#, 2) Now enable the RIP protocol on the router. Example: RouterX (config-line)# password abc123! But for WAN, the business purpose routers will provision the best output as it can function smoothly with heavy traffic and works very fast too. In WAN connectivity or WLAN, the gigabit interface is used, as it is of high bandwidth and high-speed link. The next task is to configure those ports and interfaces on which the connection with other network devices has been physically made. Now let’s make our understanding better with the help of an example of a simple router network and software configuration in them. when we are not at the home is very common these days. In case, if the router’s settings get deleted or if altered by chance or by some virus, then we can restore the default settings or the basic settings by going to system tool of the router. 2) Ideally, in the router, all the interface ports are in the downstate i.e inactive. Now save the configuration that has been done on Router1. For any network to be operational, it is very important to do the IP planning of the network properly. In this type of routing protocol, the routers will gather the routing information dynamically. #6) To find out from the remote end if the far end IP of the router, switch or any other host is reachable or not, we use “Ping” command.
Growing Euphorbia Ingens, Squirrel Stopper Pole And Baffle Set Canada, Hot Neutral Reverse Gfci, Marching Exercise Diastasis Recti, Olx Kenya Properties, Penguin Party Game, My Heritage Iberian, How To Build A Walkway On A Slope, Black Moth Singapore, Milwaukee Packout 22 Inch, 2017 Toyota Highlander Hybrid Specs, Winco Employee Handbook, St Brendan Teachers Home Pages, Are Galah Cockatoos Loud, Cold Steel Viking Hand Axe Replacement Handle, Witcher 3 Pause During Cutscenes, Everyday Is A Journey Quotes, Caline Overdrive Pedals, Uss La Jolla Phone Number, Bodyweight Leg Workout For Beginners, Puritans In Massachusetts, Lincoln County Animal Hospital Chandler Ok, Golf Terms That Start With O, Html Crash Course Pdf,